Blog 13: Nicholas Miller

NOT SHOCKING PEOPLE AFTER THEY'VE NOT SHOCKED THEMSELVES

Week 13 Rube Goldberg: Nicholas Miller

Updated Schematic of Rube Goldberg

Figure 1: Circuit Schematic

Explanation of Circuit:

So what till happen is a trail of dominoes knocked over by Abdhullah's RB will knock over a domino into a shoot which will then land on an FSR. this will allow the 555 timer to begin pulsing which will make the counter begin to send signal to the driver which will begin to count up from 0 on a 7 segment display. When the display reads 4, the XOR gate the counter is connected to will activate and send current to an opamp which will amplify the voltage to activate another set of 7 segment displays which will display B I L I M (the Turkish word for 'science'). 

While this is happening, dominoes will still be falling toward the switch which is being pressed down, until the dominoes in motion knock over the pressing mechanism which will allow voltage to reach the motor from the voltage going to the set of 7 segment displays.

POST MOTOR: The idea is that the motor will either knock over more dominoes or will push a ball towards the next circuit. (More discussion is needed ;D )

More Circuit Images

Figure 2: Force Sensing Resistor Placement

Figure 3: FSR connection to 555 Timer--> Counter--->XOR

Figure 4: Connections of 555 timer, driver, counter, and 7 segment display

Figure 5: Showcasing connection between XOR gate and OP-AMP

Figure 6: Connections to 7 segment displays that read B I L I M (Science in Turkish)

Figure 7: Domino cradle to rest on switch

Figure 8: Motor Placement

Figure 9: Full Circuit and Mechanical w/out dominoes

Figure 10: Full Circuit and Mechanical with dominoes 

Figure 11: Showcasing domino rested above its shoot to land of FSR 

Figure 12: Image of staircase domino setup for delivering domino forces to circuit (and for the hellz of a cool looking shot... kinda)

Videos of Test

Test 1: Success

Test 2: Success

Test 3: Failure

Explanations of Failures

Blog 13, Group GR

6. Group task: Explain your group RG setup.
first is Abdullah's circuit. and Op Amp connected to force sensing resistor, heavy height will connect the Op Amp to gives power to start a motor. The motor will pull dominos to pull a bottle that connected pull a wire out in the second circuit to connect the relay to power the display "by connected 555timer, counter and 7447" to count from 0 to 9. Then the motor will start and pull Corkboard to fall down and the corkboard connects Nich circuit by a thread. 

7. Group task: Video of a test run of your group RG.

Blog 13 Abdullah Alramadhan

1. Provide the updated computer drawing for your individual RG setup.

fig. 1&2: RG circuit setup

2. Explain your setup.
In my Rube Goldberg set up I have an Op Amp connected to the force sensing resistor, The Op Amp gives power to the FSR force which connects power to start a motor. The motor will pull dominos to pull a bottle that connected to a wire in the second circuit after the relay - this wire shorted the second circuit-.in the second circuit when the wire removed be the thread the powered Relay. then from the relay to 555 timers to counter which connected to 7447 to display. The display will count from 0 to 9 then the motor will start and pull Corkboard
3. Provide photos of the circuit and setup.

fig. 3,4,5 and 6: parts of the GR circuits

4. Provide at least 2 new videos of your setup in action, one being a failed attempt.

fig. 7&8: videos for GR circuits

5. What failures did you have? How did you overcome them?
1. how to connect relay, 555timer, counter and 7447. it took a long time and too many wires to connect them all together. I tried to get help from our old blogs and finally they worked.
2. how to connect the motor after display. I think I have to use "OR or XOR gate". I don't solve this problem until now.

Blog 12 Abdullah Alramadhan

1. Provide the computer drawing for your individual RG setup.

fig. 1&2: RG circuit setup

2. Explain your setup.

In my Rube Goldberg set up I have the force sensing resistor connected to an Op Amp, when we give the FSR force the Op Amp the connect with the power and it will start a motor. The motor will pull weight to another FSR in the second circuit to connect the Relay. The Relay will start display to give number 9 “out group number”, also it will start motor to pull Corkboard.  
3. Provide photos of the circuit and setup. 

fig.3: the whole circuit

fig. 4 Relay part circuit

fig. 5: Op Amp circuit

4. Provide at least 2 videos of your setup in action (parts or whole), at least one being a failed attempt.

fig. 6&7: Circuits videos 

5. What failures did you have? How did you overcome them?

a- I had a failure with the Relay, its output wasn’t accurate and it could it start the motor. At the end, we found that the Relay wasn’t working. Everything goes well when we changed it.

b- The biggest failure I had that when I connect FSR to start Rely, the voltage dropped. I think I should some resistors or something else that can make the voltage and current constant. Until now I don’t solve this problem.

Blog 12 Nicholas Miller